Chant Engineering's Pneumatic Test Stands are used to test pneumatic components used in Military Aerospace applications. Chant Pneumatic Test Stands allow the operator to test in fully automatic, semi-automatic or manual modes. This gives you the flexibility to test your components in the configuration that best suits your requirements.
Chant Engineering's Pneumatic Test Stands are complete systems with high pressure gas sources for the high pressure testing and shop air connections for the low pressure testing. The unit comes complete with computer and data acquisition software.
These test stands have proven themselves reliable in high production testing environments.
| Model |
Notable |
| 94300601 |
Universal Pneumatic Test Stand |
| |
|
| 10356 |
Pneumatic Component Test Stand |
| |
|
|
 |
Model 94300601 Test Stand Specifications:
| Dimensions: |
107" L x 60" H x 48" W |
| Weight: |
2,500 lbs |
| Electrical: |
115 VAC, 1 PH, 60Hz, 15-amp circuit |
| Pressure: |
16,000 PSI Gas, 90 PSI Air |
Model 10356 Test Stand Specifications:
Pneumatic Component Test Stand is used to test aircraft hydraulic and pneumatic components such as engine-drive hydraulic pumps, electro-hydraulic flight control assemblies, double acting hydraulic cylinders, pneumatic and hydraulic relief valves, hydro-pneumatic accumulators and other components.
The Test Stand Console consists of a 40” wide test bench with two digital display meters, an enclosed test sink area with Dynamic and Static Test circuits, and a high pressure Pneumatic Test circuit. Located along the front panel of the console are all the necessary controls to start the hydraulic pump and to control the pressures and flows to all of the test ports. The digital meters display flow and AC Volts. Also located on the console are analog pressure and temperature gauges to measure the parameters of the Unit Under Test (UUT).
The hydraulic power supply consists of a 27 GPM, 5000 Psi hydraulic pump driven by a 100 HP electric motor. The oil (designed for MIL-H-83282 or MIL-H-5606) is supplied from the 80 gallon Main Reservoir tank. The reservoir, the pump, valves, filters, flow meter and heat exchanger are all contained in one common area within the enclosure and can be accessed from the various access doors.
Test ports are located within the enclosed sink area and are used to connect the hydraulic or pneumatic systems which are used to test the integrity and functionality of the UUT.
| Dimensions: |
80" W x 72" H x 60" DP |
| Weight: |
4,000 lbs |
| Electrical: |
440 VAC, 3 PH, 60Hz, 140 FLA, SCCR 5KA |
| Pressure: |
Static: 500 – 10,000 Psig
Dynamic: 3,000-5,000 Psig
|
| Flow: |
Dynamic: 27 GPM |
| Hydraulic Fluid: |
MIL-H-83282 or MIL-H-5606 |
| Reservoir: |
80 Gallons |
| High Pressure Pump: |
Piston type – 3,000-5,000 psi |
| Heat Exchanger: |
Water system – 250,000 BTU heat removal per hour |
| Pneumatic System: |
Nitrogen BB-N-411
Compressed Nitrogen Cylinder: Operating pressure 3,000 – 3,500 Psig
Pneumatic Operation Booster: 6,000 Psig Max Pressure: 100-6,000 Psi
|
| Electrical System: |
AC Power Supply: Output Voltage 110-130 Volts, 10 Amps
DC Power Supply: 0-36 Volts
|
| Waste Tank: |
5 Gallon Tank for hydraulic waste fluid |
Chant Engineering Pneumatic Test Stands Models:
Chant Model 94300601 Test Stand:
The Chant Engineering 94300601 Pneumatic Test Stand is used to test pneumatic components used in Military Aerospace applications.
View Specifications
Chant 10356 Pneumatic Component Test Stand
Chant Engineering 10356 Pneumatic Component Test Stand is used to test aircraft hydraulic and pneumatic components such as engine-drive hydraulic pumps, electro-hydraulic flight control assemblies, double acting hydraulic cylinders, pneumatic and hydraulic relief valves, hydro-pneumatic accumulators and other components.
View Specifications
Custom configuration/capacities are available for any Test Stand; contact sales@chantengineering.com for more information.
Test Stands - Page Links:
F15 Speed Calibration |
Fatigue Cycle & Static Shaft |
Fuel Flow |
Fuel Oil
Helicopter Cargo Hook |
Hydraulic Pump |
M88A2 Advanced Unit |
Pneumatic
Servo Valve |
Servo Valve Torgue Motor |
Univeral Hydraulic
